Paracord Craft Bench ✦

Decorative cord projects

A tidy paracord key tag starts with knowing which cord does what.

A neat paracord key tag starts with knowing which cord moves and which stays still.

The cobra weave wraps a repeating knot pattern around a straight centre. Learn the parts below, then use the linked animation for the tying sequence.

Meet the parts before you start knotting.

The core is the straight cord in the middle. Working ends are the loose lengths you move around it.

A bight is a bend in a cord, not a knot. On a key tag, the core sets the woven section’s length while the working ends build its width.

“550” is a cord designation. It does not rate the strength of your finished craft.

For a 550 paracord key tag, the short sample shows how this particular cord behaves in your hands. Keep its measurements with the sample before estimating cord for the finished piece.

Give your first key tag a fighting chance.

A simple setup makes mistakes visible while they are still easy to undo.

Keep the core still

Secure the loop end of a short practice piece to a clip or board. Leave the two central strands straight; those are the core, not extra ends to weave with.

For example: Picture two railway rails with the decorative knots wrapped around them. If the rails change length while you work, the tag will change shape too.

Make the cord’s route visible

Use the step-by-step cobra animation below at a slow speed. Stop before tightening each pass so you can trace the cord in front of and behind the core.

For example: For a single-colour sample, put a removable tape label on one working end. It is easier to follow a marked end than remember which loose length was on the left.

Measure your own cord appetite

Different cord thicknesses and knot tension change how much cord a woven strip consumes. A short measured sample is more useful than assuming every tutorial’s cutting length fits your project.

For example: Measure the working ends before and after a 3cm sample. Use the difference to estimate a longer piece, leaving extra for the attachment and finish.

Put the idea to work

Why is my cobra weave turning into a spiral?

A flat cobra weave alternates the direction of successive half-knots. Keep making the same-sided half-knot and the work tends to spiral.

That can be a deliberate decorative effect; if you wanted a flat key tag, it is a clue to check the sequence.

Core = the straight centre. Working ends = the loose lengths you move. This identifies the parts; use the external animation for the tying sequence.
  1. Check direction before pulling tight. Compare the next loose knot with the corresponding animation step. A mistaken pass is much easier to reverse while you can still see the crossing.Try this: Make two opposing half-knots, then check whether the woven section lies flat before continuing.
  2. Watch the core, not just the outside edges. Tightening the working ends should snug the pattern around the core. If you drag the core through the attachment, you also change the woven section’s intended length.Try this: Mark the core’s intended end with removable tape and check whether that mark is creeping upwards.
  3. Fix a bunch rather than crushing it. Several uneven knots forced together can hide a wrong crossing. Back out to the first repeat that looks different, then rebuild it with consistent tension.Try this: Compare the spaces beside the core at the start and finish of a short sample, as well as its overall length.

Decorative cord projects

Make the sample earn its place on your keyring.

Lay the trial tag beside the keys you actually carry. Decide how much woven cord gives you something to grab without making the bunch bulky.

Test the attachment and practise the finishing steps shown in the guide on the sample before cutting the working ends short.

Less useful

Cut every cord to a length from a different bracelet tutorial.

More specific

Make a measured sample, choose the tag’s length, then allow cord for its own attachment and finish.

Keep this project decorative. A key tag or zipper pull is a useful first object; it is not a climbing, rescue or load-support system.

Guides from other websites

Further reading

Follow an external guide, then try one thing.

External guide · animatedknots.com

Animated Knots: cobra lanyard ↗

Follow the animated sequence for a decorative lanyard knot. Compare the direction of each pass before tightening your own sample.

Put it into practice: Step through the cobra animation and identify the core and working ends before copying a crossing.

Make a 3cm diagnostic sample

You need craft cord, a way to hold the loop steady and a ruler. Follow the linked guide for its exact setup and finish.

  1. Mark one working end and measure the loose lengths before tying.
  2. Follow the cobra guide slowly until you have about 3cm of weaving.
  3. Lay it flat and inspect the first place where the direction or spacing changes.
  4. Measure the remaining cord and keep the sample with a note about its size.